--$ XILINX$RCSfile: xcs30xl_tq144.bsd,v $
--$ XILINX$Revision: 1.4 $
--
-- BSDL file for device XCS30XL, package TQ144
-- Xilinx, Inc. $State: FINAL $ $Date: 2002-01-29 14:11:36-08 $
-- Generated by createBSDL 2.10
--
-- For technical support, contact Xilinx as follows:
-- North America 1-800-255-7778 hotline@xilinx.com
-- United Kingdom +44 870 7350 610 eurosupport@xilinx.com
-- France (33) 1 3463 0100 eurosupport@xilinx.com
-- Germany (49) 89 991 54930 eurosupport@xilinx.com
-- Japan (81) 3-3297-9163 jhotline@xilinx.com
--
-- BSDL verified to conform to 1149.1b-1994 syntax. This device has been
-- tested by the Intellitech 1149.1 Verification Lab using the Intellitech
-- Eclipse(TM) Scan Diagnostic Tool and the Intellitech RCT(TM). This
-- device has been verified to operate according to the BSDL provided,
-- and is compatible with the IEEE 1149.1 standard when the operating
-- instructions in the BSDL are followed.
-- PH: 603-868-7116 or email: scansupport@intellitech.com
--
-- This BSDL file reflects the pre-configuration JTAG behavior. To reflect
-- the post-configuration JTAG behavior (if any), edit this file as described
-- below. Many of these changes are demonstrated by commented-out template
-- lines preceeding the lines they would replace:
--
-- 1. Enable USER instructions as appropriate (see below).
-- 2. For inputs using uncontrolled paths (e.g. PGCK, SGCK), change
-- boundary cell function from 'input' to 'clock' or 'observe_only'.
-- 3. Set disable result of all pads as configured.
-- 4. Set safe state of boundary cells as necessary.
-- 5. Set safe state of INIT output to X, or as necessary (see below).
-- 6. Rename entity if necessary to avoid name collisions.
-- 7. Change INIT port direction from "in" to "inout" (see below).
-- 8. Change COMPLIANCE_PATTERNS to "(LPWRB,PROGRAM) (11)" (see below).
-- 9. Change INIT boundary cells from internal to controlr, output3,
-- and input, respectively (see below).
-- 10. Remove the design warning regarding keeping INIT low.
--
-- NOTE: Post-configuration JTAG is available only if the BSCAN symbol
-- is instantiated in the FPGA design.
-- NOTE: PULLUP symbols must be instantiated on the TMS and TDI pins
-- in the FPGA design to comply with IEEE Std. 1149.1-1993.
entity XCS30XL_TQ144 is
generic (PHYSICAL_PIN_MAP : string := "TQ144" );
port (
CCLK: linkage bit;
DONE: linkage bit;
GND: linkage bit_vector (1 to 16);
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line so
-- that INIT is of type inout.
-- INIT: inout bit;
INIT: in bit;
IO2: inout bit;
IO3: inout bit;
IO4: inout bit;
IO5: inout bit;
IO9: inout bit;
IO10: inout bit;
IO15: inout bit;
IO16: inout bit;
IO22: inout bit;
IO23: inout bit;
IO27: inout bit;
IO28: inout bit;
IO29: inout bit;
IO30: inout bit;
IO33: inout bit;
IO34: inout bit;
IO35: inout bit;
IO36: inout bit;
IO47: inout bit;
IO48: inout bit;
IO50: inout bit;
IO58: inout bit;
IO59: inout bit;
IO60: inout bit;
IO61: inout bit;
IO64: inout bit;
IO65: inout bit;
IO66: inout bit;
IO67: inout bit;
IO75: inout bit;
IO76: inout bit;
IO77: inout bit;
IO78: inout bit;
IO87: inout bit;
IO88: inout bit;
IO89: inout bit;
IO90: inout bit;
IO91: inout bit;
IO92: inout bit;
IO98: inout bit;
IO99: inout bit;
IO100: inout bit;
IO101: inout bit;
IO102: inout bit;
IO103: inout bit;
IO112: inout bit;
IO113: inout bit;
IO114: inout bit;
IO115: inout bit;
IO123: inout bit;
IO124: inout bit;
IO125: inout bit;
IO129: inout bit;
IO130: inout bit;
IO131: inout bit;
IO132: inout bit;
IO140: inout bit;
IO141: inout bit;
IO142: inout bit;
IO143: inout bit;
IO152: inout bit;
IO153: inout bit;
IO154: inout bit;
IO155: inout bit;
IO156: inout bit;
IO157: inout bit;
IO162: inout bit;
IO163: inout bit;
IO164: inout bit;
IO165: inout bit;
IO169: inout bit;
IO170: inout bit;
IO178: inout bit;
IO179: inout bit;
IO182: inout bit;
IO183: inout bit;
IO187: inout bit;
IO188: inout bit;
IO189: inout bit;
IO190: inout bit;
IO193: inout bit;
IO194: inout bit;
IO195: inout bit;
IO196: inout bit;
IO200: inout bit;
IO201: inout bit;
IO204: inout bit;
IO205: inout bit;
IO216: inout bit;
IO217: inout bit;
IO218: inout bit;
IO219: inout bit;
IO220: inout bit;
IO221: inout bit;
IO226: inout bit;
IO227: inout bit;
IO228: inout bit;
IO229: inout bit;
IO230: inout bit;
IO231: inout bit;
IO235: inout bit;
IO240: inout bit;
IO241: inout bit;
IO246: inout bit;
IO247: inout bit;
IO251: inout bit;
IO252: inout bit;
IO253: inout bit;
IO254: inout bit;
LPWRB: in bit;
M0: in bit;
M1: inout bit;
PROGRAM: in bit;
TCK: in bit;
TDI: in bit;
TDO: out bit;
TMS: in bit;
VCC: linkage bit_vector (1 to 8)
); --end port list
use STD_1149_1_1994.all;
attribute COMPONENT_CONFORMANCE of XCS30XL_TQ144 : entity is
"STD_1149_1_1993";
attribute PIN_MAP of XCS30XL_TQ144 : entity is PHYSICAL_PIN_MAP;
constant TQ144: PIN_MAP_STRING:=
"CCLK:P107," &
"DONE:P72," &
"GND:(P137,P1,P8,P17,P27,P35,P45,P55,P64,P71," &
"P81,P91,P100,P110,P118,P127)," &
"INIT:P53," &
"IO2:P129," &
"IO3:P130," &
"IO4:P131," &
"IO5:P132," &
"IO9:P133," &
"IO10:P134," &
"IO15:P135," &
"IO16:P136," &
"IO22:P138," &
"IO23:P139," &
"IO27:P140," &
"IO28:P141," &
"IO29:P142," &
"IO30:P143," &
"IO33:P2," &
"IO34:P3," &
"IO35:P4," &
"IO36:P5," &
"IO47:P9," &
"IO48:P10," &
"IO50:P12," &
"IO58:P13," &
"IO59:P14," &
"IO60:P15," &
"IO61:P16," &
"IO64:P19," &
"IO65:P20," &
"IO66:P21," &
"IO67:P22," &
"IO75:P23," &
"IO76:P24," &
"IO77:P25," &
"IO78:P26," &
"IO87:P28," &
"IO88:P29," &
"IO89:P30," &
"IO90:P31," &
"IO91:P32," &
"IO92:P33," &
"IO98:P39," &
"IO99:P40," &
"IO100:P41," &
"IO101:P42," &
"IO102:P43," &
"IO103:P44," &
"IO112:P46," &
"IO113:P47," &
"IO114:P48," &
"IO115:P49," &
"IO123:P50," &
"IO124:P51," &
"IO125:P52," &
"IO129:P56," &
"IO130:P57," &
"IO131:P58," &
"IO132:P59," &
"IO140:P60," &
"IO141:P61," &
"IO142:P62," &
"IO143:P63," &
"IO152:P65," &
"IO153:P66," &
"IO154:P67," &
"IO155:P68," &
"IO156:P69," &
"IO157:P70," &
"IO162:P75," &
"IO163:P76," &
"IO164:P77," &
"IO165:P78," &
"IO169:P79," &
"IO170:P80," &
"IO178:P82," &
"IO179:P83," &
"IO182:P84," &
"IO183:P85," &
"IO187:P86," &
"IO188:P87," &
"IO189:P88," &
"IO190:P89," &
"IO193:P92," &
"IO194:P93," &
"IO195:P94," &
"IO196:P95," &
"IO200:P96," &
"IO201:P97," &
"IO204:P98," &
"IO205:P99," &
"IO216:P101," &
"IO217:P102," &
"IO218:P103," &
"IO219:P104," &
"IO220:P105," &
"IO221:P106," &
"IO226:P111," &
"IO227:P112," &
"IO228:P113," &
"IO229:P114," &
"IO230:P115," &
"IO231:P116," &
"IO235:P117," &
"IO240:P119," &
"IO241:P120," &
"IO246:P121," &
"IO247:P122," &
"IO251:P123," &
"IO252:P124," &
"IO253:P125," &
"IO254:P126," &
"LPWRB:P38," &
"M0:P36," &
"M1:P34," &
"PROGRAM:P74," &
"TCK:P7," &
"TDI:P6," &
"TDO:P109," &
"TMS:P11," &
"VCC:(P128,P144,P18,P37,P54,P73,P90,P108)";
--end pin map
attribute TAP_SCAN_IN of TDI : signal is true;
attribute TAP_SCAN_MODE of TMS : signal is true;
attribute TAP_SCAN_OUT of TDO : signal is true;
attribute TAP_SCAN_CLOCK of TCK : signal is (2.0e6, LOW);
-- This is conservative. Real max is expected to be (~5MHz, BOTH).
attribute COMPLIANCE_PATTERNS of XCS30XL_TQ144 : entity is
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the corresponding line
-- below.
-- "(PROGRAM,LPWRB) (11)";
--
-- NOTE: If INIT has been high or floating since the later of power-on
-- and the last rising transition of PROGRAM, then the device may
-- be in configuration mode in which case some JTAG instructions
-- will not be available.
"(INIT,PROGRAM,LPWRB) (011)";
attribute INSTRUCTION_LENGTH of XCS30XL_TQ144 : entity is 3;
attribute INSTRUCTION_OPCODE of XCS30XL_TQ144 : entity is
"SAMPLE (001)," & -- Internal capture not valid until after config
"IDCODE (110)," &
"READBACK (100)," & -- Not available during configuration
"CONFIGURE (101)," & -- Not available during configuration
"USER2 (011)," & -- Not available until after configuration
"USER1 (010)," & -- Not available until after configuration
"EXTEST (000)," & -- Not available during configuration
"BYPASS (111)";
attribute INSTRUCTION_CAPTURE of XCS30XL_TQ144 : entity is "X01";
-- MSB of instruction capture is low during configuration.
-- If the device is configured, and a USER instruction is implemented
-- and not private to the FPGA designer, then it should be removed
-- from INSTRUCTION_PRIVATE, and the target register should be defined
-- in REGISTER_ACCESS.
attribute INSTRUCTION_PRIVATE of XCS30XL_TQ144 : entity is
"USER1," &
"USER2," &
"READBACK," &
"CONFIGURE";
attribute IDCODE_REGISTER of XCS30XL_TQ144 : entity is
"XXXX" & -- version
"0000010" & -- family
"000011000" & -- array size
"00001001001" & -- manufacturer
"1"; -- required by 1149.1
attribute REGISTER_ACCESS of XCS30XL_TQ144 : entity is
-- "<reg_name>[<length>] (USER1)," &
-- "<reg_name>[<length>] (USER2)," &
"BYPASS (BYPASS)," &
"DEVICE_ID (IDCODE)," &
"BOUNDARY (SAMPLE,EXTEST)";
attribute BOUNDARY_LENGTH of XCS30XL_TQ144 : entity is 583;
attribute BOUNDARY_REGISTER of XCS30XL_TQ144 : entity is
-- cellnum (type, port, function, safe[, ccell, disval, disrslt])
" 0 (BC_1, *, internal, X)," &
" 1 (BC_1, *, internal, X)," &
" 2 (BC_1, *, controlr, 1)," &
" 3 (BC_1, IO226, output3, X, 2, 1, PULL1)," &
" 4 (BC_1, IO226, input, X)," &
" 5 (BC_1, *, controlr, 1)," &
" 6 (BC_1, IO227, output3, X, 5, 1, PULL1)," &
" 7 (BC_1, IO227, input, X)," &
" 8 (BC_1, *, controlr, 1)," &
" 9 (BC_1, IO228, output3, X, 8, 1, PULL1)," &
" 10 (BC_1, IO228, input, X)," &
" 11 (BC_1, *, controlr, 1)," &
" 12 (BC_1, IO229, output3, X, 11, 1, PULL1)," &
" 13 (BC_1, IO229, input, X)," &
" 14 (BC_1, *, controlr, 1)," &
" 15 (BC_1, IO230, output3, X, 14, 1, PULL1)," &
" 16 (BC_1, IO230, input, X)," &
" 17 (BC_1, *, controlr, 1)," &
" 18 (BC_1, IO231, output3, X, 17, 1, PULL1)," &
" 19 (BC_1, IO231, input, X)," &
" 20 (BC_1, *, internal, 1)," & -- IO233.T
" 21 (BC_1, *, internal, X)," & -- IO233.O
" 22 (BC_1, *, internal, X)," & -- IO233.I
" 23 (BC_1, *, internal, 1)," & -- IO234.T
" 24 (BC_1, *, internal, X)," & -- IO234.O
" 25 (BC_1, *, internal, X)," & -- IO234.I
" 26 (BC_1, *, controlr, 1)," &
" 27 (BC_1, IO235, output3, X, 26, 1, PULL1)," &
" 28 (BC_1, IO235, input, X)," &
" 29 (BC_1, *, internal, 1)," & -- IO236.T
" 30 (BC_1, *, internal, X)," & -- IO236.O
" 31 (BC_1, *, internal, X)," & -- IO236.I
" 32 (BC_1, *, internal, 1)," & -- IO237.T
" 33 (BC_1, *, internal, X)," & -- IO237.O
" 34 (BC_1, *, internal, X)," & -- IO237.I
" 35 (BC_1, *, internal, 1)," & -- IO238.T
" 36 (BC_1, *, internal, X)," & -- IO238.O
" 37 (BC_1, *, internal, X)," & -- IO238.I
" 38 (BC_1, *, controlr, 1)," &
" 39 (BC_1, IO240, output3, X, 38, 1, PULL1)," &
" 40 (BC_1, IO240, input, X)," &
" 41 (BC_1, *, controlr, 1)," &
" 42 (BC_1, IO241, output3, X, 41, 1, PULL1)," &
" 43 (BC_1, IO241, input, X)," &
" 44 (BC_1, *, internal, 1)," & -- IO242.T
" 45 (BC_1, *, internal, X)," & -- IO242.O
" 46 (BC_1, *, internal, X)," & -- IO242.I
" 47 (BC_1, *, internal, 1)," & -- IO243.T
" 48 (BC_1, *, internal, X)," & -- IO243.O
" 49 (BC_1, *, internal, X)," & -- IO243.I
" 50 (BC_1, *, controlr, 1)," &
" 51 (BC_1, IO246, output3, X, 50, 1, PULL1)," &
" 52 (BC_1, IO246, input, X)," &
" 53 (BC_1, *, controlr, 1)," &
" 54 (BC_1, IO247, output3, X, 53, 1, PULL1)," &
" 55 (BC_1, IO247, input, X)," &
" 56 (BC_1, *, internal, 1)," & -- IO249.T
" 57 (BC_1, *, internal, X)," & -- IO249.O
" 58 (BC_1, *, internal, X)," & -- IO249.I
" 59 (BC_1, *, internal, 1)," & -- IO250.T
" 60 (BC_1, *, internal, X)," & -- IO250.O
" 61 (BC_1, *, internal, X)," & -- IO250.I
" 62 (BC_1, *, controlr, 1)," &
" 63 (BC_1, IO251, output3, X, 62, 1, PULL1)," &
" 64 (BC_1, IO251, input, X)," &
" 65 (BC_1, *, controlr, 1)," &
" 66 (BC_1, IO252, output3, X, 65, 1, PULL1)," &
" 67 (BC_1, IO252, input, X)," &
" 68 (BC_1, *, controlr, 1)," &
" 69 (BC_1, IO253, output3, X, 68, 1, PULL1)," &
" 70 (BC_1, IO253, input, X)," &
" 71 (BC_1, *, controlr, 1)," &
" 72 (BC_1, IO254, output3, X, 71, 1, PULL1)," &
" 73 (BC_1, IO254, input, X)," &
" 74 (BC_1, *, controlr, 1)," &
" 75 (BC_1, IO2, output3, X, 74, 1, PULL1)," &
" 76 (BC_1, IO2, input, X)," &
" 77 (BC_1, *, controlr, 1)," &
" 78 (BC_1, IO3, output3, X, 77, 1, PULL1)," &
" 79 (BC_1, IO3, input, X)," &
" 80 (BC_1, *, controlr, 1)," &
" 81 (BC_1, IO4, output3, X, 80, 1, PULL1)," &
" 82 (BC_1, IO4, input, X)," &
" 83 (BC_1, *, controlr, 1)," &
" 84 (BC_1, IO5, output3, X, 83, 1, PULL1)," &
" 85 (BC_1, IO5, input, X)," &
" 86 (BC_1, *, internal, 1)," & -- IO6.T
" 87 (BC_1, *, internal, X)," & -- IO6.O
" 88 (BC_1, *, internal, X)," & -- IO6.I
" 89 (BC_1, *, internal, 1)," & -- IO7.T
" 90 (BC_1, *, internal, X)," & -- IO7.O
" 91 (BC_1, *, internal, X)," & -- IO7.I
" 92 (BC_1, *, controlr, 1)," &
" 93 (BC_1, IO9, output3, X, 92, 1, PULL1)," &
" 94 (BC_1, IO9, input, X)," &
" 95 (BC_1, *, controlr, 1)," &
" 96 (BC_1, IO10, output3, X, 95, 1, PULL1)," &
" 97 (BC_1, IO10, input, X)," &
" 98 (BC_1, *, internal, 1)," & -- IO13.T
" 99 (BC_1, *, internal, X)," & -- IO13.O
" 100 (BC_1, *, internal, X)," & -- IO13.I
" 101 (BC_1, *, internal, 1)," & -- IO14.T
" 102 (BC_1, *, internal, X)," & -- IO14.O
" 103 (BC_1, *, internal, X)," & -- IO14.I
" 104 (BC_1, *, controlr, 1)," &
" 105 (BC_1, IO15, output3, X, 104, 1, PULL1)," &
" 106 (BC_1, IO15, input, X)," &
" 107 (BC_1, *, controlr, 1)," &
" 108 (BC_1, IO16, output3, X, 107, 1, PULL1)," &
" 109 (BC_1, IO16, input, X)," &
" 110 (BC_1, *, internal, 1)," & -- IO18.T
" 111 (BC_1, *, internal, X)," & -- IO18.O
" 112 (BC_1, *, internal, X)," & -- IO18.I
" 113 (BC_1, *, internal, 1)," & -- IO19.T
" 114 (BC_1, *, internal, X)," & -- IO19.O
" 115 (BC_1, *, internal, X)," & -- IO19.I
" 116 (BC_1, *, internal, 1)," & -- IO20.T
" 117 (BC_1, *, internal, X)," & -- IO20.O
" 118 (BC_1, *, internal, X)," & -- IO20.I
" 119 (BC_1, *, internal, 1)," & -- IO21.T
" 120 (BC_1, *, internal, X)," & -- IO21.O
" 121 (BC_1, *, internal, X)," & -- IO21.I
" 122 (BC_1, *, controlr, 1)," &
" 123 (BC_1, IO22, output3, X, 122, 1, PULL1)," &
" 124 (BC_1, IO22, input, X)," &
" 125 (BC_1, *, controlr, 1)," &
" 126 (BC_1, IO23, output3, X, 125, 1, PULL1)," &
" 127 (BC_1, IO23, input, X)," &
" 128 (BC_1, *, internal, 1)," & -- IO25.T
" 129 (BC_1, *, internal, X)," & -- IO25.O
" 130 (BC_1, *, internal, X)," & -- IO25.I
" 131 (BC_1, *, internal, 1)," & -- IO26.T
" 132 (BC_1, *, internal, X)," & -- IO26.O
" 133 (BC_1, *, internal, X)," & -- IO26.I
" 134 (BC_1, *, controlr, 1)," &
" 135 (BC_1, IO27, output3, X, 134, 1, PULL1)," &
" 136 (BC_1, IO27, input, X)," &
" 137 (BC_1, *, controlr, 1)," &
" 138 (BC_1, IO28, output3, X, 137, 1, PULL1)," &
" 139 (BC_1, IO28, input, X)," &
" 140 (BC_1, *, controlr, 1)," &
" 141 (BC_1, IO29, output3, X, 140, 1, PULL1)," &
" 142 (BC_1, IO29, input, X)," &
" 143 (BC_1, *, controlr, 1)," &
" 144 (BC_1, IO30, output3, X, 143, 1, PULL1)," &
" 145 (BC_1, IO30, input, X)," &
" 146 (BC_1, *, controlr, 1)," &
" 147 (BC_1, IO33, output3, X, 146, 1, PULL1)," &
" 148 (BC_1, IO33, input, X)," &
" 149 (BC_1, *, controlr, 1)," &
" 150 (BC_1, IO34, output3, X, 149, 1, PULL1)," &
" 151 (BC_1, IO34, input, X)," &
" 152 (BC_1, *, controlr, 1)," &
" 153 (BC_1, IO35, output3, X, 152, 1, PULL1)," &
" 154 (BC_1, IO35, input, X)," &
" 155 (BC_1, *, controlr, 1)," &
" 156 (BC_1, IO36, output3, X, 155, 1, PULL1)," &
" 157 (BC_1, IO36, input, X)," &
" 158 (BC_1, *, internal, X)," &
" 159 (BC_1, *, internal, X)," &
" 160 (BC_1, *, internal, X)," &
" 161 (BC_1, *, internal, X)," &
" 162 (BC_1, *, internal, X)," &
" 163 (BC_1, *, internal, X)," &
" 164 (BC_1, *, internal, 1)," & -- IO40.T
" 165 (BC_1, *, internal, X)," & -- IO40.O
" 166 (BC_1, *, internal, X)," & -- IO40.I
" 167 (BC_1, *, internal, 1)," & -- IO41.T
" 168 (BC_1, *, internal, X)," & -- IO41.O
" 169 (BC_1, *, internal, X)," & -- IO41.I
" 170 (BC_1, *, internal, 1)," & -- IO42.T
" 171 (BC_1, *, internal, X)," & -- IO42.O
" 172 (BC_1, *, internal, X)," & -- IO42.I
" 173 (BC_1, *, internal, 1)," & -- IO43.T
" 174 (BC_1, *, internal, X)," & -- IO43.O
" 175 (BC_1, *, internal, X)," & -- IO43.I
" 176 (BC_1, *, internal, 1)," & -- IO44.T
" 177 (BC_1, *, internal, X)," & -- IO44.O
" 178 (BC_1, *, internal, X)," & -- IO44.I
" 179 (BC_1, *, internal, 1)," & -- IO45.T
" 180 (BC_1, *, internal, X)," & -- IO45.O
" 181 (BC_1, *, internal, X)," & -- IO45.I
" 182 (BC_1, *, controlr, 1)," &
" 183 (BC_1, IO47, output3, X, 182, 1, PULL1)," &
" 184 (BC_1, IO47, input, X)," &
" 185 (BC_1, *, controlr, 1)," &
" 186 (BC_1, IO48, output3, X, 185, 1, PULL1)," &
" 187 (BC_1, IO48, input, X)," &
" 188 (BC_1, *, internal, X)," &
" 189 (BC_1, *, internal, X)," &
" 190 (BC_1, *, internal, X)," &
" 191 (BC_1, *, controlr, 1)," &
" 192 (BC_1, IO50, output3, X, 191, 1, PULL1)," &
" 193 (BC_1, IO50, input, X)," &
" 194 (BC_1, *, internal, 1)," & -- IO53.T
" 195 (BC_1, *, internal, X)," & -- IO53.O
" 196 (BC_1, *, internal, X)," & -- IO53.I
" 197 (BC_1, *, internal, 1)," & -- IO54.T
" 198 (BC_1, *, internal, X)," & -- IO54.O
" 199 (BC_1, *, internal, X)," & -- IO54.I
" 200 (BC_1, *, internal, 1)," & -- IO56.T
" 201 (BC_1, *, internal, X)," & -- IO56.O
" 202 (BC_1, *, internal, X)," & -- IO56.I
" 203 (BC_1, *, internal, 1)," & -- IO57.T
" 204 (BC_1, *, internal, X)," & -- IO57.O
" 205 (BC_1, *, internal, X)," & -- IO57.I
" 206 (BC_1, *, controlr, 1)," &
" 207 (BC_1, IO58, output3, X, 206, 1, PULL1)," &
" 208 (BC_1, IO58, input, X)," &
" 209 (BC_1, *, controlr, 1)," &
" 210 (BC_1, IO59, output3, X, 209, 1, PULL1)," &
" 211 (BC_1, IO59, input, X)," &
" 212 (BC_1, *, controlr, 1)," &
" 213 (BC_1, IO60, output3, X, 212, 1, PULL1)," &
" 214 (BC_1, IO60, input, X)," &
" 215 (BC_1, *, controlr, 1)," &
" 216 (BC_1, IO61, output3, X, 215, 1, PULL1)," &
" 217 (BC_1, IO61, input, X)," &
" 218 (BC_1, *, controlr, 1)," &
" 219 (BC_1, IO64, output3, X, 218, 1, PULL1)," &
" 220 (BC_1, IO64, input, X)," &
" 221 (BC_1, *, controlr, 1)," &
" 222 (BC_1, IO65, output3, X, 221, 1, PULL1)," &
" 223 (BC_1, IO65, input, X)," &
" 224 (BC_1, *, controlr, 1)," &
" 225 (BC_1, IO66, output3, X, 224, 1, PULL1)," &
" 226 (BC_1, IO66, input, X)," &
" 227 (BC_1, *, controlr, 1)," &
" 228 (BC_1, IO67, output3, X, 227, 1, PULL1)," &
" 229 (BC_1, IO67, input, X)," &
" 230 (BC_1, *, internal, 1)," & -- IO68.T
" 231 (BC_1, *, internal, X)," & -- IO68.O
" 232 (BC_1, *, internal, X)," & -- IO68.I
" 233 (BC_1, *, internal, 1)," & -- IO69.T
" 234 (BC_1, *, internal, X)," & -- IO69.O
" 235 (BC_1, *, internal, X)," & -- IO69.I
" 236 (BC_1, *, internal, 1)," & -- IO71.T
" 237 (BC_1, *, internal, X)," & -- IO71.O
" 238 (BC_1, *, internal, X)," & -- IO71.I
" 239 (BC_1, *, internal, 1)," & -- IO72.T
" 240 (BC_1, *, internal, X)," & -- IO72.O
" 241 (BC_1, *, internal, X)," & -- IO72.I
" 242 (BC_1, *, controlr, 1)," &
" 243 (BC_1, IO75, output3, X, 242, 1, PULL1)," &
" 244 (BC_1, IO75, input, X)," &
" 245 (BC_1, *, controlr, 1)," &
" 246 (BC_1, IO76, output3, X, 245, 1, PULL1)," &
" 247 (BC_1, IO76, input, X)," &
" 248 (BC_1, *, controlr, 1)," &
" 249 (BC_1, IO77, output3, X, 248, 1, PULL1)," &
" 250 (BC_1, IO77, input, X)," &
" 251 (BC_1, *, controlr, 1)," &
" 252 (BC_1, IO78, output3, X, 251, 1, PULL1)," &
" 253 (BC_1, IO78, input, X)," &
" 254 (BC_1, *, internal, 1)," & -- IO80.T
" 255 (BC_1, *, internal, X)," & -- IO80.O
" 256 (BC_1, *, internal, X)," & -- IO80.I
" 257 (BC_1, *, internal, 1)," & -- IO81.T
" 258 (BC_1, *, internal, X)," & -- IO81.O
" 259 (BC_1, *, internal, X)," & -- IO81.I
" 260 (BC_1, *, internal, 1)," & -- IO82.T
" 261 (BC_1, *, internal, X)," & -- IO82.O
" 262 (BC_1, *, internal, X)," & -- IO82.I
" 263 (BC_1, *, internal, 1)," & -- IO83.T
" 264 (BC_1, *, internal, X)," & -- IO83.O
" 265 (BC_1, *, internal, X)," & -- IO83.I
" 266 (BC_1, *, internal, 1)," & -- IO84.T
" 267 (BC_1, *, internal, X)," & -- IO84.O
" 268 (BC_1, *, internal, X)," & -- IO84.I
" 269 (BC_1, *, internal, 1)," & -- IO85.T
" 270 (BC_1, *, internal, X)," & -- IO85.O
" 271 (BC_1, *, internal, X)," & -- IO85.I
" 272 (BC_1, *, controlr, 1)," &
" 273 (BC_1, IO87, output3, X, 272, 1, PULL1)," &
" 274 (BC_1, IO87, input, X)," &
" 275 (BC_1, *, controlr, 1)," &
" 276 (BC_1, IO88, output3, X, 275, 1, PULL1)," &
" 277 (BC_1, IO88, input, X)," &
" 278 (BC_1, *, controlr, 1)," &
" 279 (BC_1, IO89, output3, X, 278, 1, PULL1)," &
" 280 (BC_1, IO89, input, X)," &
" 281 (BC_1, *, controlr, 1)," &
" 282 (BC_1, IO90, output3, X, 281, 1, PULL1)," &
" 283 (BC_1, IO90, input, X)," &
" 284 (BC_1, *, controlr, 1)," &
" 285 (BC_1, IO91, output3, X, 284, 1, PULL1)," &
" 286 (BC_1, IO91, input, X)," &
" 287 (BC_1, *, controlr, 1)," &
" 288 (BC_1, IO92, output3, X, 287, 1, PULL1)," &
" 289 (BC_1, IO92, input, X)," &
" 290 (BC_1, *, controlr, 1)," &
" 291 (BC_1, M1, output3, X, 290, 1, PULL1)," &
" 292 (BC_1, M1, input, X)," &
" 293 (BC_1, M0, input, X)," &
" 294 (BC_1, *, controlr, 1)," &
" 295 (BC_1, IO98, output3, X, 294, 1, PULL1)," &
" 296 (BC_1, IO98, input, X)," &
" 297 (BC_1, *, controlr, 1)," &
" 298 (BC_1, IO99, output3, X, 297, 1, PULL1)," &
" 299 (BC_1, IO99, input, X)," &
" 300 (BC_1, *, controlr, 1)," &
" 301 (BC_1, IO100, output3, X, 300, 1, PULL1)," &
" 302 (BC_1, IO100, input, X)," &
" 303 (BC_1, *, controlr, 1)," &
" 304 (BC_1, IO101, output3, X, 303, 1, PULL1)," &
" 305 (BC_1, IO101, input, X)," &
" 306 (BC_1, *, controlr, 1)," &
" 307 (BC_1, IO102, output3, X, 306, 1, PULL1)," &
" 308 (BC_1, IO102, input, X)," &
" 309 (BC_1, *, controlr, 1)," &
" 310 (BC_1, IO103, output3, X, 309, 1, PULL1)," &
" 311 (BC_1, IO103, input, X)," &
" 312 (BC_1, *, internal, 1)," & -- IO105.T
" 313 (BC_1, *, internal, X)," & -- IO105.O
" 314 (BC_1, *, internal, X)," & -- IO105.I
" 315 (BC_1, *, internal, 1)," & -- IO106.T
" 316 (BC_1, *, internal, X)," & -- IO106.O
" 317 (BC_1, *, internal, X)," & -- IO106.I
" 318 (BC_1, *, internal, 1)," & -- IO107.T
" 319 (BC_1, *, internal, X)," & -- IO107.O
" 320 (BC_1, *, internal, X)," & -- IO107.I
" 321 (BC_1, *, internal, 1)," & -- IO108.T
" 322 (BC_1, *, internal, X)," & -- IO108.O
" 323 (BC_1, *, internal, X)," & -- IO108.I
" 324 (BC_1, *, internal, 1)," & -- IO109.T
" 325 (BC_1, *, internal, X)," & -- IO109.O
" 326 (BC_1, *, internal, X)," & -- IO109.I
" 327 (BC_1, *, internal, 1)," & -- IO110.T
" 328 (BC_1, *, internal, X)," & -- IO110.O
" 329 (BC_1, *, internal, X)," & -- IO110.I
" 330 (BC_1, *, controlr, 1)," &
" 331 (BC_1, IO112, output3, X, 330, 1, PULL1)," &
" 332 (BC_1, IO112, input, X)," &
" 333 (BC_1, *, controlr, 1)," &
" 334 (BC_1, IO113, output3, X, 333, 1, PULL1)," &
" 335 (BC_1, IO113, input, X)," &
" 336 (BC_1, *, controlr, 1)," &
" 337 (BC_1, IO114, output3, X, 336, 1, PULL1)," &
" 338 (BC_1, IO114, input, X)," &
" 339 (BC_1, *, controlr, 1)," &
" 340 (BC_1, IO115, output3, X, 339, 1, PULL1)," &
" 341 (BC_1, IO115, input, X)," &
" 342 (BC_1, *, internal, 1)," & -- IO118.T
" 343 (BC_1, *, internal, X)," & -- IO118.O
" 344 (BC_1, *, internal, X)," & -- IO118.I
" 345 (BC_1, *, internal, 1)," & -- IO119.T
" 346 (BC_1, *, internal, X)," & -- IO119.O
" 347 (BC_1, *, internal, X)," & -- IO119.I
" 348 (BC_1, *, internal, 1)," & -- IO121.T
" 349 (BC_1, *, internal, X)," & -- IO121.O
" 350 (BC_1, *, internal, X)," & -- IO121.I
" 351 (BC_1, *, internal, 1)," & -- IO122.T
" 352 (BC_1, *, internal, X)," & -- IO122.O
" 353 (BC_1, *, internal, X)," & -- IO122.I
" 354 (BC_1, *, controlr, 1)," &
" 355 (BC_1, IO123, output3, X, 354, 1, PULL1)," &
" 356 (BC_1, IO123, input, X)," &
" 357 (BC_1, *, controlr, 1)," &
" 358 (BC_1, IO124, output3, X, 357, 1, PULL1)," &
" 359 (BC_1, IO124, input, X)," &
" 360 (BC_1, *, controlr, 1)," &
" 361 (BC_1, IO125, output3, X, 360, 1, PULL1)," &
" 362 (BC_1, IO125, input, X)," &
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line.
-- Repeat for registers 363 through 365.
-- " 363 (BC_1, *, controlr, 1)," &
" 363 (BC_1, *, internal, 1)," &
-- " 364 (BC_1, INIT, output3, X, 363, 1, PULL1)," &
" 364 (BC_1, *, internal, 0)," &
-- " 365 (BC_1, INIT, input, X)," &
" 365 (BC_1, *, internal, X)," &
" 366 (BC_1, *, controlr, 1)," &
" 367 (BC_1, IO129, output3, X, 366, 1, PULL1)," &
" 368 (BC_1, IO129, input, X)," &
" 369 (BC_1, *, controlr, 1)," &
" 370 (BC_1, IO130, output3, X, 369, 1, PULL1)," &
" 371 (BC_1, IO130, input, X)," &
" 372 (BC_1, *, controlr, 1)," &
" 373 (BC_1, IO131, output3, X, 372, 1, PULL1)," &
" 374 (BC_1, IO131, input, X)," &
" 375 (BC_1, *, controlr, 1)," &
" 376 (BC_1, IO132, output3, X, 375, 1, PULL1)," &
" 377 (BC_1, IO132, input, X)," &
" 378 (BC_1, *, internal, 1)," & -- IO133.T
" 379 (BC_1, *, internal, X)," & -- IO133.O
" 380 (BC_1, *, internal, X)," & -- IO133.I
" 381 (BC_1, *, internal, 1)," & -- IO134.T
" 382 (BC_1, *, internal, X)," & -- IO134.O
" 383 (BC_1, *, internal, X)," & -- IO134.I
" 384 (BC_1, *, internal, 1)," & -- IO136.T
" 385 (BC_1, *, internal, X)," & -- IO136.O
" 386 (BC_1, *, internal, X)," & -- IO136.I
" 387 (BC_1, *, internal, 1)," & -- IO137.T
" 388 (BC_1, *, internal, X)," & -- IO137.O
" 389 (BC_1, *, internal, X)," & -- IO137.I
" 390 (BC_1, *, controlr, 1)," &
" 391 (BC_1, IO140, output3, X, 390, 1, PULL1)," &
" 392 (BC_1, IO140, input, X)," &
" 393 (BC_1, *, controlr, 1)," &
" 394 (BC_1, IO141, output3, X, 393, 1, PULL1)," &
" 395 (BC_1, IO141, input, X)," &
" 396 (BC_1, *, controlr, 1)," &
" 397 (BC_1, IO142, output3, X, 396, 1, PULL1)," &
" 398 (BC_1, IO142, input, X)," &
" 399 (BC_1, *, controlr, 1)," &
" 400 (BC_1, IO143, output3, X, 399, 1, PULL1)," &
" 401 (BC_1, IO143, input, X)," &
" 402 (BC_1, *, internal, 1)," & -- IO145.T
" 403 (BC_1, *, internal, X)," & -- IO145.O
" 404 (BC_1, *, internal, X)," & -- IO145.I
" 405 (BC_1, *, internal, 1)," & -- IO146.T
" 406 (BC_1, *, internal, X)," & -- IO146.O
" 407 (BC_1, *, internal, X)," & -- IO146.I
" 408 (BC_1, *, internal, 1)," & -- IO147.T
" 409 (BC_1, *, internal, X)," & -- IO147.O
" 410 (BC_1, *, internal, X)," & -- IO147.I
" 411 (BC_1, *, internal, 1)," & -- IO148.T
" 412 (BC_1, *, internal, X)," & -- IO148.O
" 413 (BC_1, *, internal, X)," & -- IO148.I
" 414 (BC_1, *, internal, 1)," & -- IO149.T
" 415 (BC_1, *, internal, X)," & -- IO149.O
" 416 (BC_1, *, internal, X)," & -- IO149.I
" 417 (BC_1, *, internal, 1)," & -- IO150.T
" 418 (BC_1, *, internal, X)," & -- IO150.O
" 419 (BC_1, *, internal, X)," & -- IO150.I
" 420 (BC_1, *, controlr, 1)," &
" 421 (BC_1, IO152, output3, X, 420, 1, PULL1)," &
" 422 (BC_1, IO152, input, X)," &
" 423 (BC_1, *, controlr, 1)," &
" 424 (BC_1, IO153, output3, X, 423, 1, PULL1)," &
" 425 (BC_1, IO153, input, X)," &
" 426 (BC_1, *, controlr, 1)," &
" 427 (BC_1, IO154, output3, X, 426, 1, PULL1)," &
" 428 (BC_1, IO154, input, X)," &
" 429 (BC_1, *, controlr, 1)," &
" 430 (BC_1, IO155, output3, X, 429, 1, PULL1)," &
" 431 (BC_1, IO155, input, X)," &
" 432 (BC_1, *, controlr, 1)," &
" 433 (BC_1, IO156, output3, X, 432, 1, PULL1)," &
" 434 (BC_1, IO156, input, X)," &
" 435 (BC_1, *, controlr, 1)," &
" 436 (BC_1, IO157, output3, X, 435, 1, PULL1)," &
" 437 (BC_1, IO157, input, X)," &
" 438 (BC_1, *, controlr, 1)," &
" 439 (BC_1, IO162, output3, X, 438, 1, PULL1)," &
" 440 (BC_1, IO162, input, X)," &
" 441 (BC_1, *, controlr, 1)," &
" 442 (BC_1, IO163, output3, X, 441, 1, PULL1)," &
" 443 (BC_1, IO163, input, X)," &
" 444 (BC_1, *, controlr, 1)," &
" 445 (BC_1, IO164, output3, X, 444, 1, PULL1)," &
" 446 (BC_1, IO164, input, X)," &
" 447 (BC_1, *, controlr, 1)," &
" 448 (BC_1, IO165, output3, X, 447, 1, PULL1)," &
" 449 (BC_1, IO165, input, X)," &
" 450 (BC_1, *, internal, 1)," & -- IO166.T
" 451 (BC_1, *, internal, X)," & -- IO166.O
" 452 (BC_1, *, internal, X)," & -- IO166.I
" 453 (BC_1, *, internal, 1)," & -- IO167.T
" 454 (BC_1, *, internal, X)," & -- IO167.O
" 455 (BC_1, *, internal, X)," & -- IO167.I
" 456 (BC_1, *, controlr, 1)," &
" 457 (BC_1, IO169, output3, X, 456, 1, PULL1)," &
" 458 (BC_1, IO169, input, X)," &
" 459 (BC_1, *, controlr, 1)," &
" 460 (BC_1, IO170, output3, X, 459, 1, PULL1)," &
" 461 (BC_1, IO170, input, X)," &
" 462 (BC_1, *, internal, 1)," & -- IO171.T
" 463 (BC_1, *, internal, X)," & -- IO171.O
" 464 (BC_1, *, internal, X)," & -- IO171.I
" 465 (BC_1, *, internal, 1)," & -- IO172.T
" 466 (BC_1, *, internal, X)," & -- IO172.O
" 467 (BC_1, *, internal, X)," & -- IO172.I
" 468 (BC_1, *, internal, 1)," & -- IO173.T
" 469 (BC_1, *, internal, X)," & -- IO173.O
" 470 (BC_1, *, internal, X)," & -- IO173.I
" 471 (BC_1, *, internal, 1)," & -- IO174.T
" 472 (BC_1, *, internal, X)," & -- IO174.O
" 473 (BC_1, *, internal, X)," & -- IO174.I
" 474 (BC_1, *, internal, 1)," & -- IO176.T
" 475 (BC_1, *, internal, X)," & -- IO176.O
" 476 (BC_1, *, internal, X)," & -- IO176.I
" 477 (BC_1, *, internal, 1)," & -- IO177.T
" 478 (BC_1, *, internal, X)," & -- IO177.O
" 479 (BC_1, *, internal, X)," & -- IO177.I
" 480 (BC_1, *, controlr, 1)," &
" 481 (BC_1, IO178, output3, X, 480, 1, PULL1)," &
" 482 (BC_1, IO178, input, X)," &
" 483 (BC_1, *, controlr, 1)," &
" 484 (BC_1, IO179, output3, X, 483, 1, PULL1)," &
" 485 (BC_1, IO179, input, X)," &
" 486 (BC_1, *, controlr, 1)," &
" 487 (BC_1, IO182, output3, X, 486, 1, PULL1)," &
" 488 (BC_1, IO182, input, X)," &
" 489 (BC_1, *, controlr, 1)," &
" 490 (BC_1, IO183, output3, X, 489, 1, PULL1)," &
" 491 (BC_1, IO183, input, X)," &
" 492 (BC_1, *, internal, 1)," & -- IO185.T
" 493 (BC_1, *, internal, X)," & -- IO185.O
" 494 (BC_1, *, internal, X)," & -- IO185.I
" 495 (BC_1, *, internal, 1)," & -- IO186.T
" 496 (BC_1, *, internal, X)," & -- IO186.O
" 497 (BC_1, *, internal, X)," & -- IO186.I
" 498 (BC_1, *, controlr, 1)," &
" 499 (BC_1, IO187, output3, X, 498, 1, PULL1)," &
" 500 (BC_1, IO187, input, X)," &
" 501 (BC_1, *, controlr, 1)," &
" 502 (BC_1, IO188, output3, X, 501, 1, PULL1)," &
" 503 (BC_1, IO188, input, X)," &
" 504 (BC_1, *, controlr, 1)," &
" 505 (BC_1, IO189, output3, X, 504, 1, PULL1)," &
" 506 (BC_1, IO189, input, X)," &
" 507 (BC_1, *, controlr, 1)," &
" 508 (BC_1, IO190, output3, X, 507, 1, PULL1)," &
" 509 (BC_1, IO190, input, X)," &
" 510 (BC_1, *, controlr, 1)," &
" 511 (BC_1, IO193, output3, X, 510, 1, PULL1)," &
" 512 (BC_1, IO193, input, X)," &
" 513 (BC_1, *, controlr, 1)," &
" 514 (BC_1, IO194, output3, X, 513, 1, PULL1)," &
" 515 (BC_1, IO194, input, X)," &
" 516 (BC_1, *, controlr, 1)," &
" 517 (BC_1, IO195, output3, X, 516, 1, PULL1)," &
" 518 (BC_1, IO195, input, X)," &
" 519 (BC_1, *, controlr, 1)," &
" 520 (BC_1, IO196, output3, X, 519, 1, PULL1)," &
" 521 (BC_1, IO196, input, X)," &
" 522 (BC_1, *, internal, 1)," & -- IO197.T
" 523 (BC_1, *, internal, X)," & -- IO197.O
" 524 (BC_1, *, internal, X)," & -- IO197.I
" 525 (BC_1, *, internal, 1)," & -- IO198.T
" 526 (BC_1, *, internal, X)," & -- IO198.O
" 527 (BC_1, *, internal, X)," & -- IO198.I
" 528 (BC_1, *, controlr, 1)," &
" 529 (BC_1, IO200, output3, X, 528, 1, PULL1)," &
" 530 (BC_1, IO200, input, X)," &
" 531 (BC_1, *, controlr, 1)," &
" 532 (BC_1, IO201, output3, X, 531, 1, PULL1)," &
" 533 (BC_1, IO201, input, X)," &
" 534 (BC_1, *, controlr, 1)," &
" 535 (BC_1, IO204, output3, X, 534, 1, PULL1)," &
" 536 (BC_1, IO204, input, X)," &
" 537 (BC_1, *, controlr, 1)," &
" 538 (BC_1, IO205, output3, X, 537, 1, PULL1)," &
" 539 (BC_1, IO205, input, X)," &
" 540 (BC_1, *, internal, 1)," & -- IO206.T
" 541 (BC_1, *, internal, X)," & -- IO206.O
" 542 (BC_1, *, internal, X)," & -- IO206.I
" 543 (BC_1, *, internal, 1)," & -- IO207.T
" 544 (BC_1, *, internal, X)," & -- IO207.O
" 545 (BC_1, *, internal, X)," & -- IO207.I
" 546 (BC_1, *, internal, 1)," & -- IO209.T
" 547 (BC_1, *, internal, X)," & -- IO209.O
" 548 (BC_1, *, internal, X)," & -- IO209.I
" 549 (BC_1, *, internal, 1)," & -- IO210.T
" 550 (BC_1, *, internal, X)," & -- IO210.O
" 551 (BC_1, *, internal, X)," & -- IO210.I
" 552 (BC_1, *, internal, 1)," & -- IO211.T
" 553 (BC_1, *, internal, X)," & -- IO211.O
" 554 (BC_1, *, internal, X)," & -- IO211.I
" 555 (BC_1, *, internal, 1)," & -- IO212.T
" 556 (BC_1, *, internal, X)," & -- IO212.O
" 557 (BC_1, *, internal, X)," & -- IO212.I
" 558 (BC_1, *, internal, 1)," & -- IO213.T
" 559 (BC_1, *, internal, X)," & -- IO213.O
" 560 (BC_1, *, internal, X)," & -- IO213.I
" 561 (BC_1, *, internal, 1)," & -- IO214.T
" 562 (BC_1, *, internal, X)," & -- IO214.O
" 563 (BC_1, *, internal, X)," & -- IO214.I
" 564 (BC_1, *, controlr, 1)," &
" 565 (BC_1, IO216, output3, X, 564, 1, PULL1)," &
" 566 (BC_1, IO216, input, X)," &
" 567 (BC_1, *, controlr, 1)," &
" 568 (BC_1, IO217, output3, X, 567, 1, PULL1)," &
" 569 (BC_1, IO217, input, X)," &
" 570 (BC_1, *, controlr, 1)," &
" 571 (BC_1, IO218, output3, X, 570, 1, PULL1)," &
" 572 (BC_1, IO218, input, X)," &
" 573 (BC_1, *, controlr, 1)," &
" 574 (BC_1, IO219, output3, X, 573, 1, PULL1)," &
" 575 (BC_1, IO219, input, X)," &
" 576 (BC_1, *, controlr, 1)," &
" 577 (BC_1, IO220, output3, X, 576, 1, PULL1)," &
" 578 (BC_1, IO220, input, X)," &
" 579 (BC_1, *, controlr, 1)," &
" 580 (BC_1, IO221, output3, X, 579, 1, PULL1)," &
" 581 (BC_1, IO221, input, X)," &
" 582 (BC_1, *, internal, X)";
--end boundary register
attribute DESIGN_WARNING of XCS30XL_TQ144 : entity is
"LPWRB, CLK and DONE are not represented in BOUNDARY_REGISTER." &
"This BSDL file must be modified by the FPGA designer in order to" &
"reflect post-configuration behavior (if any)." &
"If INIT has been high or floating since power-on or the last" &
"rising edge of PROGRAM, then the device may be in" &
"configuration mode in which case this file is not valid." &
"The output and tristate capture values are not valid until after" &
"the device is configured." &
"The fast output mux (where used) is not captured properly." &
"The tristate control is not captured properly when GTS is activated." &
"Some pins have both controlled and uncontrolled input paths.";
end XCS30XL_TQ144;
